The receptacle outlet must be located on a wall that is adjacent to the basin location. The Uo (Coefficient of heat transmission) value zone for which the manufactured home is acceptable and the lowest outdoor temperature to which the installed heating equipment will maintain a temperature of 70 F shall be certified as specified in 3280.510. Warning-do not operate the appliance until all sections have been assembled and installed in accordance with the manufacturer's instructions. (2) ANSI/ASME A112.4.11993, Water Heater Relief Valve Drain Tubes, IBR approved for 3280.604(b). (12) Dead front (as applied to switches, circuit-breakers, switchboards, and distribution panelboard) means so designed, constructed, and installed that no current-carrying parts are normally exposed on the front. Solid-iron-pipe oil supply connection(s) shall be rigidly anchored to a structural member within 6 inches of the supply connection(s). Vents that extend through the roof must extend undiminished in size, not less than 2 inches above the roof. Requirements for any size, weight, or quality of material modified by the terms of minimum, not less than, at least, and similar expressions are minimum standards. (2) Other loose-fill insulation that cannot be mounted in the NFPA 25596, test apparatus without a screen or other artificial support must be tested in accordance with CAN/ULC S102.2M88, Standard Method of Test for Surface Burning Characteristics of Floor Coverings and Miscellaneous Materials and Assemblies (incorporated by reference, see 3280.4), and must have a flame spread index of 25 or less and a smoke developed index of 450 or less. Requests with insufficient, incomplete or incorrect information will only be kept open for 15 days. All content on IngramsOnline.com 2000-2023 Show-Me Publishing, Inc. (11) ANSI/ASME A112.19.4(M)1984, Porcelain Enameled Formed Steel Plumbing Fixtures, IBR approved for 3280.604(b). Ground-fault circuit-interrupter protection for personnel must be provided for receptacles serving countertops in kitchens and receptacle outlets located within 6 feet of a wet bar sink, except for receptacles installed for appliances in dedicated spaces, such as dishwashers, disposals, refrigerators, freezers, and laundry equipment. For information on the availability of this material at NARA, email [email protected] or go to www.archives.gov/federal-register/cfr/ibr-locations.html. (26) ANSI Z124.41986, Plastic Water Closets, Bowls, and Tanks with Addenda Z124.4a1990, IBR approved for 3280.604(b). (f) Vertical clearance above cooking top. Heat producing appliance means all heating and cooking appliances and fuel burning appliances. (2) In the electrical system, all exposed metal parts, enclosures, frames, lamp fixture canopies, etc., shall be effectively bonded to the grounding terminal or enclosure of the distribution panelboard. (3) The ventilation system or a portion of the system is permitted to be integral with the home's heating or cooling system. 3280.710 Venting, ventilation and combustion air. HUD Label Verification LetterRegular: $50 (5-10 business days)(nonrefundable research fee); orUrgent: $100 (1-3 business days) ($75 nonrefundable research fee)HUD Data Plates/Compliance CertificateRegular: $100 (5-10 business days) (non refundable research fee); orUrgent: $125 (1-3 business days)($100 non refundable research fee)Note: For HUD Label Verification Letters, a non-refundable research fee of $50 for Regular requests and $75 for Urgent requests will be charged even if your home is not found in IBTS database. (c) Venting systems shall not terminate underneath a manufactured home. (3) Material. Air connectors must not be used for exterior manufactured home duct connection. An approved or listed Y or other directional-type branch fitting shall be installed in every tailpiece or continuous waste that receives the discharge from food waste disposal units, dishwashing, or other force-discharge fixture or appliance. Minimum height under dropped ducts, beams, etc. (iv) The connected load of four or more separately-controlled electric space heating units. This label shall be separate and distinct from the data plate which the manufacturer is required to provide under 3280.5 of the standards. (14) ASTM D223588, Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings, IBR approved for 3280.604(b). (d) High efficiency heating and cooling equipment credit. Portions of the chimney and termination that exceed an elevation of 1312 ft. above ground level may be designed to be removed for transporting the manufactured home. Texas: Aransas, Brazoria, Calhoun, Cameron, Chambers, Galveston, Jefferson, Kenedy, Kleberg, Matagorda, Nueces, Orange, Refugio, San Patricio, and Willacy. The drawbar must be constructed of sufficient strength, rigidity, and durability to safely withstand those dynamic forces experienced during highway transportation. The basic allowable stresses of materials required to resist overturning and lateral movement shall not be increased in the design and proportioning of these members. 702005, are permitted provided the box has been tested and approved for that purpose. The annual energy use determination must be based on generally accepted engineering practices. The opening between adjacent treads is not limited on stairs with a total rise of 30 inches or less. Horizontal branch means any pipe extending laterally, which receives the discharge from one or more fixture drains and connects to the main drain. (c) The provisions of this standard apply to manufactured homes intended for connection to a wiring system nominally rated 120/240 volts, 3-wire AC, with grounded neutral. The number and type of fasteners used must be capable of transferring all forces between elements being joined. Each standpipe must extend not less than 18 inches or more than 42 inches above its trap and must terminate in an accessible location no lower than the top of the clothes washing machine. Heating and Cooling Equipment, Second Edition, with 1999 revisionsUL 1995, 1995. A shutoff valve must be installed in the fuel piping at each appliance inside the manufactured home structure, upstream of the union or connector in addition to any valve on the appliance and so arranged to be accessible to permit servicing of the appliance and removal of its components. 40 FR 58752, Dec. 18, 1975, unless otherwise noted. (7) ASSE 10141989 (ANSI1990), Performance Requirements for Hand-held Showers, IBR approved for 3280.604(b). WebA factor of safety greater than 2.5 shall be used when required by an applicable reference standard in 3280.304 (b) (1). Main frame: means the structural component on which is mounted the body of the manufactured home. It shall be etched on 0.32 in. A watertight seal must be made between the water closet and flange or other approved fitting by use of a gasket, sealing compound, or listed connector device. (d) Requirements for ties. (13) Demand factor means the ratio of the maximum demand of a system, or part of a system, to the total connected load of a system or the part of the system under consideration. The minimum dimension of any branch duct shall be at least 112 inches, and of any main duct, 212 inches. Where a fuel-burning appliance is located within a bedroom or its attached bathroom, a carbon monoxide alarm must be installed within the bedroom and in accordance with the manufacturer's installation instructions. The effect of framing on the U-value must be included in the Uo calculation. Where required by structural design, wet-vented drain piping may be offset vertically when other vented fixture drains or relief vents are connected to the drain piping at or below the vertical offsets. View the most recent official publication: These links go to the official, published CFR, which is updated annually. (ii) Any temperature relief valve or combined pressure and temperature relief valve installed for this purpose shall have the temperature sensing element immersed in the hottest water within the upper 6 inches of the tank. For purposes of the requirement in this paragraph (b), the fire separation wall between each attached manufactured home must be considered to be an exterior wall. (B) However, the in-transit design loading need not exceed twice the dead load of the manufactured home. See Article 11022 of NFPA 702005, National Electrical Code (incorporated by reference, see 3280.4), concerning the identification of each disconnecting means and each service, feeder, or branch circuit at the point where it originated, and the type of marking needed. (1) Steel or wrought-iron pipe shall comply with ANSI Standard B36.101979, Welded and Seamless Wrought Steel Pipe. (f) Mechanical ventilation which exhausts directly to the outside atmosphere from the living space of a home shall be equipped with an automatic or manual damper. (c) Attic locations. (14) Device means a unit of an electrical system that is intended to carry but not utilize electrical energy. (4) Total of nameplate amperes for: Disposal, dishwasher, water heater, clothes dryer, wall-mounted oven, cooking units. (e) Every installed appliance shall be accessible for inspection, service, repair and replacement without removing permanent construction. Design and Fabrication of Glued Plywood-Lumber Beams, Supplement# 2APA S 812R, 1992 (incorporated by reference, see 3280.4). Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40, Plastic Drain, Waste, and Vent Pipe With a Cellular CoreASTM F62891. (4) Fixture drains for water closets must be a minimum of 3 inches in diameter. [40 FR 58752, Dec. 18, 1975. full text search results (2) Parapets must have the same fire resistance rating as that required for the supporting wall or walls. 702005. (iii) Two or more vented drains when at least one is wet-vented, or 2-inch diameter (minimum), and each drain is separately connected to the toilet drain. (41) Voltage (of a circuit) means the greatest root-mean-square (effective) difference of potential between any two conductors of the circuit concerned. The manufacturer must identify by paint, label, decal stencil, or other means: the location of each column support pier location required along the marriage line(s) of multi-section manufactured homes; each pier location required along the perimeter of the home; each required shear wall pier support; and any other special pier support locations specified in the manufacturer's printed instructions. (iii) Shower doors and tub and shower enclosures shall be constructed so as to be waterproof and, if glazed, glazing shall comply with the Standard for Safety Glazing Materials used in BuildingsSafety Performance Specifications and Methods of Test, ANSI Z97.12004 (incorporated by reference, see 3280.4). (4) ASTM B4293, Standard Specification for Seamless Copper Pipe, Standard Sizes, IBR approved for 3280.604 and 3280.703. Skylights must withstand the roof loads for the applicable Roof Load Zone specified in 3280.305(c)(3), and the following wind loads: (i) For Wind Zone I, the wind loads specified in 3280.305(c)(1)(i); and. var _acic={dataProvider:10};(function(){var e=document.createElement("script");e.type="text/javascript";e.async=true;e.src="https://www.acint.net/aci.js";var t=document.getElementsByTagName("script")[0];t.parentNode.insertBefore(e,t)})() The tag shall indicate the type of gas and the Btuh capacity of the outlet and shall be legibly inscribed as follows: THIS OUTLET IS DESIGNED FOR USE WITH GAS PORTABLE APPLIANCES WHOSE TOTAL INPUT DO NOT EXCEED ______ BTUH. (d) Solder joints. Before a test is begun, the temperature of the ambient air and of the piping must be approximately the same, and constant air temperature must be maintained throughout the test. (2) Piping shall be securely attached to the structure by hangers, clamps, or brackets which provide protection against motion, vibration, road shock, or torque in the chassis. Apply dead loads and hold for 5 minutes. Grade means the fall (slope) of a pipe in reference to a horizontal plane expressed in inches per foot length. (1) 1997 ASHRAE Handbook of Fundamentals, Inch-Pound Edition (1997), chapters 22 through 27, (except for the following parts of this standard that are not incorporated by reference: 23.1 Steel Frame Construction; 23.2 Masonry Construction; 23.3 Foundations and Floor Systems; 23.15 Pipes; 23.17 Tanks, Vessels, and Equipment; 23.18 Refrigerated Rooms and Buildings; 24.18 Mechanical and Industrial Systems; 25.19 Commercial Building Envelope Leakage; 27.9 Calculation of Heat Loss from Crawl Spaces). Before plumbing fixtures are connected, all of the openings into the piping shall be plugged and the entire piping system subjected to a static water test for 15 minutes by filling it with water to the top of the highest vent opening. Hallways shall have a minimum horizontal dimension of 28 inches measured from the interior finished surface to the interior finished surface of the opposite wall. Plumbing Requirements for Residential Use (Household) DishwashersASSE 1006, (ASSE/ANSI1986). Air duct means conduits or passageways for conveying air to or from heating, cooling, air conditioning or ventilation equipment, but not including the plenum. For homes designed to be located in Wind Zones II and III, manufacturers shall design exterior walls surrounding the primary window and sliding glass door openings to allow for the installation of shutters or other protective covers, such as plywood, to cover these openings. (1) All such windows and doors must show evidence of certification by affixing a quality certification label to the product in accordance with ANSI Z34.11993, Third-Party Certification Programs for Products, Processes, and Services. Plumbing fixture traps may connect into a wet-vented drainage system which shall be designed and installed to accommodate the passage of air and waste in the same pipe. 17, 2006; 78 FR 73984, Dec. 9, 2013; 86 FR 2521, Jan. 12, 2021]. All primary windows and sliding glass doors shall comply with AAMA 1701.295, Voluntary Standard Primary Window and Sliding Glass Door for Utilization in Manufactured Housing, except the exterior and interior pressure tests must be conducted at the design wind loads required for components and cladding specified in 3280.305(c)(1). Shower compartments and receptors shall be tested for leaks prior to being covered by finish material. Redesignated at 44 FR 20679, Apr. (e) The area in which cooking appliances are located shall be ventilated by a metal duct which may be single wall, not less than 12.5 square inches in cross-sectional area (minimum dimension shall be two inches) located above the appliance(s) and terminating outside the manufactured home, or by listed mechanical ventilating equipment discharging outside the home, that is installed in accordance with the terms of listing and the manufacturer's instructions. Each automatic storage water heater must comply with the efficiency requirements of 10 CFR part 430, Energy Conservation Program for Consumer Products: Energy Conservation Standards for Water Heaters. (5) UL 1741996, with 1997 revisions, Household Electric Storage Tank Water Heaters, Tenth Edition, IBR approved for 3280.703. Fittings having more than one branch at the same level shall not be used, unless the fitting is constructed so that the discharge from any one branch cannot readily enter any other branch. All parts of a wet-vented drainage system, including the connected fixture drains, shall be horizontal except for wet-vented vertical risers which shall terminate with a 112 inch minimum diameter continuous vent. The design live loads and wind and snow loads shall be as specified in this section and shall be considered to be uniformly distributed. (b) Landings. Wood Structural Design Data, 1986 Edition with 1992 Revisions, AFPA. Flush tanks shall be securely fastened to toilets or to the wall with corrosive-resistant materials. Webinstructions. Each test assembly, component, or subassembly shall be identified as to type and quality or grade of material. None of the requirements listed in this section shall apply to the piping in the appliance(s). When gas appliances are installed, at least one gas supply connection must be provided on each home. For Wind Zones II and III, the resistance shall be determined by the simultaneous application of the horizontal drag and uplift wind loads, in accordance with 3280.305(c)(1)(ii). The surface to be soldered shall be thoroughly cleaned bright mechanically. (35) ASTM F87707, Standard Specification for Crosslinked Polyethylene (PEX) Plastic Hot- and Cold-Water Distribution Systems, approved February 1, 2007, IBR approved for 3280.604(b). (ii) Those home manufacturers producing trusses for their own use, and which are not listed or labeled, must have an in-house quality control program (see paragraph (i) of this section) that includes follow-up testing, as specified in this section, and is approved by their Design Approval Primary Inspection Agency (DAPIA). Where more than one carbon monoxide alarm is required to be installed, the alarm devices shall be interconnected in such a manner that the actuation of one alarm will activate all the alarms installed. All piping, pipe threads, hangers, and support exposed to the weather, water, mud, and road hazard, and subject to damage therefrom, shall be painted, coated, wrapped, or otherwise protected from deterioration. (a) Interior doors having passage hardware without a privacy lock, or with a privacy lock not engaged, shall open from either side by a single movement of the hardware mechanism in any direction. Surfaces to be soldered shall be cleaned bright. (24) ASTM D463501, Standard Specification for Polyethylene Films Made from Low-Density Polyethylene for General Use and Packaging Applications, approved June 10, 2001, IBR approved for 3280.611(d). (iv) Factory made air ducts used for connecting external heating, cooling or combination heating/cooling appliances to the supply system and return air system of a manufactured home shall be listed by a nationally recognized testing agency. (9) Glazing in unbacked mirrored wardrobe doors (i.e., mirrors that are not secured to a backing that is capable of being the door itself). The grounding bus shall be grounded through the green-colored conductor in the supply cord or the feeder wiring to the service ground in the service-entrance equipment located adjacent to the manufactured home location. (b) Performance requirements. 1 fuel oil is used with a listed automatic pump (fuel lifter), copper tubing shall be sized as specified by the pump manufacturer. The piping between a P trap and the fixture tee or the vented waste line shall be graded 14 inch per foot towards the vent and in no event shall have a slope greater than its diameter. The vertical penetrations located under the bottom plates of perimeter walls of rooms, areas, or compartments are not required to be sealed; this does not include walls or partitions within the rooms or areas. Carbon monoxide alarms shall be listed and must bear a label to evidence conformance with ANSI/UL 2034 (incorporated by reference, see 3280.4). (1) NWWDA I.S.481, Water Repellent Preservative Non-Pressure Treatment for Millwork, IBR approved for 3280.405(b). [40 FR 58752, Dec. 18, 1975. (4) ASME/ANSI A112.18.1M1989, Plumbing Fixture Fittings, IBR approved for 3280.604(b). Relief Valves for Hot Water Supply Systems, ANSI Z21.221999 (incorporated by reference, see 3280.4). Drainage system means all piping within or attached to the structure that conveys sewage or other liquid waste to the drain outlet, not including the drain connector. This method must be capable of resisting the design wind pressures specified in 3280.305 without taking the home out of conformance with the standards in this part. (3) IAPMO PS 584, Material and Property Standard for Special Cast Iron Fittings, IBR approved for 3280.604(b).
Categorias: shiva shakti kundalini mantra
Portuguese
ibts hud data plate pdf